47 open source boards using the DRV2605LDGS

Real designs built with the DRV2605LDGS, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

47 boardsClear filters|Most starred

How designs wire the DRV2605LDGS

Read from the KiCad layouts of 36 open source designs, one per repository: what each pin of the DRV2605LDGS connects to, and the resistors, capacitors and other passives placed on it.

  • The REG pin has a capacitor to GND on 34 of 36 designs, most often 1 µF (then 100 nF).
  • The VDD pin has a decoupling capacitor on 27 of 35 designs, most often 1 µF (then 100 nF).
  • The SCL pin has a pull-up to 3.3V on 25 of 36 designs, most often 10 kΩ (then 2.2 kΩ).
  • The SDA pin has a pull-up to 3.3V on 25 of 36 designs, most often 4.7 kΩ (then 10 kΩ).
REGpin 1Connected to: Signal 100%
  • Capacitor to GND on 94% · 1 µF (31), 100 nF (1), 10 µF (1)
SCLpin 2Connected to: The microcontroller 42%, a connector 33%
  • Pull-up to 3.3V on 69% · 10 kΩ (11), 2.2 kΩ (9), 4.7 kΩ (9)
SDApin 3Connected to: The microcontroller 42%, a connector 33%
  • Pull-up to 3.3V on 69% · 4.7 kΩ (10), 10 kΩ (10), 2.2 kΩ (9)
VDD/NCpin 6Connected to: 3.3V 61% · not connected 22% · a signal 17%
  • Decoupling capacitor on 67% · 1 µF (20), 100 nF (8), 10 µF (8)
GNDpin 8Connected to: GND 97%
VDDpin 10Connected to: 3.3V 86%
  • Decoupling capacitor on 77% · 1 µF (22), 100 nF (9), 10 µF (7)

4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Haptic drv2605l by sadekbaroudi, Meko by KOEGlike, Main by zzeneg and Triangulate-ES 01-Watch by sandgum.

The DRV2605LDGS in open source designs

The gallery holds 47 open source boards using the DRV2605LDGS from 36 GitHub repositories; a typical one measures about 80.5 × 74.6 mm and carries around 52 components.

51% are two-layer designs, the rest use four layers or more, and 47% carry an open source license.

The most starred is Haptic drv2605l by sadekbaroudi.

Microcontrollers on boards using the DRV2605LDGS

DRV2605LDGS: common questions

Where can I find a DRV2605LDGS reference design?

Each of the 47 boards on this page is a real design using the DRV2605LDGS. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the DRV2605LDGS REG pin connected?

The REG pin has a capacitor to GND on 34 of 36 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 36 open source designs using the DRV2605LDGS.

What decoupling capacitors do designs use on the DRV2605LDGS VDD pin?

The VDD pin has a decoupling capacitor on 27 of 35 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 36 open source designs using the DRV2605LDGS.

What pull-up resistor is used on the DRV2605LDGS SCL pin?

The SCL pin has a pull-up to 3.3V on 25 of 36 designs, most often 10 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 36 open source designs using the DRV2605LDGS.

What parts are used alongside the DRV2605LDGS?

The TCA9548APWR, AP2112K-3.3, ESP32-S3-MINI-1, LIS3DH and LSM6DS3 appear in the most repositories here.

Which microcontrollers do boards using the DRV2605LDGS use?

Most are built on ESP32 (18), RP2040/RP2350 (3), Nordic nRF (2) and AVR/Arduino (1).

How big is a typical board using the DRV2605LDGS?

The median is 80.5 × 74.6 mm, and 51% are two-layer designs.

What is the most popular open source board using the DRV2605LDGS?

By GitHub stars, Haptic drv2605l by sadekbaroudi, with 220 stars.

Can I simulate one of these boards using the DRV2605LDGS before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part