30 open source boards using the 74LS148
Real designs built with the 74LS148, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
68000
jefftranter
134.6 × 208.3 mm90 parts2LNo license132PIC
.C68
ProbablyNotArtyom
214 × 170 mm184 parts4LGPL-2.051M68kcomp1
jtsiomb
159.5 × 99.8 mm50 parts2LCC-BY-SA-4.032Yddraig
ddraig68k
340 × 210 mm214 parts4LMIT29RC200-Dev Backplane
MarkD833
188 × 102.9 mm90 parts2LCC-BY-NC-4.08PIC
Colecovision multicart
sparkletron
70.1 × 74.6 mm14 parts2LMIT5Vic20-32k ram cart
The8BitEnthusiast
90 × 45 mm5 parts2LMIT4Km discrete adc
KnoxMakers
99.1 × 94 mm66 parts2LNo license3Steve 68k
stevegg
177 × 140.7 mm91 parts2LNo license2Hydra-16
danstruthers
304.8 × 243.8 mm199 parts6LNo license1Amix 68k (r0)
SmallRobot2000
333.4 × 149.9 mm169 parts4LNo license1Proto1
ehbc-project
254 × 254 mm166 parts4LNo license0STM32
ProgtomataBoard
hlvs-gnc
3.6 × 3.2 mm62 parts2LNo license0Tangentbord
JAndersM
115.6 × 95.9 mm61 parts2LGPL-3.00MC68000
ppsilv
257.6 × 228.4 mm58 parts2LGPL-3.00TriBit-Lux
XEMACS-666
80 × 41 mm57 parts2LNo license0AVR/Arduino
Stepper motor controller
FibStack
65 × 56.5 mm32 parts2LCustom license0AVR/Arduino
VIC Cart 1
hansliss
126.5 × 74.8 mm27 parts2LAGPL-3.00PIC
Copy
ProbablyNotArtyom
214 × 170 mm184 parts4LGPL-2.051Amix 68k(r1)
SmallRobot2000
333.4 × 149.9 mm169 parts4LNo license1ReZyklus.memory cartridge
jeroenhn
73.7 × 45.1 mm48 parts2LNo license1468302 CPU Board
MarkD833
101.6 × 53.3 mm37 parts4LCC-BY-NC-4.08ADC-3-bit
Trilobyte-CPU
46.2 × 33.5 mm47 parts4LNo license2CPU Board
stevegg
99.8 × 99.8 mm29 parts2LNo license2Amix 68k r2
SmallRobot2000
333.4 × 149.9 mm169 parts4LNo license1RC201-68000 CPU 2
MarkD833
101.6 × 53.3 mm37 parts4LCC-BY-NC-4.08Poly88 cpu daughterboard
abzman
46.4 × 29.2 mm4 parts2LUnlicense3Amix 68k r2 (T1)
SmallRobot2000
333.4 × 149.9 mm169 parts4LNo license168000 CPU Board
MarkD833
101.6 × 53.3 mm32 parts4LCC-BY-NC-4.08ADC-Decoder-Controller
Trilobyte-CPU
45.2 × 57.9 mm23 parts4LNo license2
How designs wire the 74LS148
Read from the KiCad layouts of 21 open source designs, one per repository: what each pin of the 74LS148 connects to, and the resistors, capacitors and other passives placed on it.
- The EI pin is tied to GND on 18 of 21 designs (a signal on 2).
- The EO pin is left unconnected on 17 of 21 designs (a signal on 4).
- The I2 pin has a pull-up to 5V on 13 of 21 designs, most often 4.7 kΩ (then 10 kΩ).
- The I3 pin has a pull-up to 5V on 13 of 21 designs, most often 4.7 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| I4pin 1 | Connected to: A connector 29% · 5V 19% |
|
| I5pin 2 | Connected to: A connector 38% |
|
| I6pin 3 | Connected to: A connector 33% |
|
| I7pin 4 | Connected to: A connector 29% |
|
| EIpin 5 | Connected to: GND 86% | — |
| GNDpin 8 | Connected to: GND 100% | — |
| IOpin 10 | Connected to: A connector 24% · GND 19% |
|
| I1pin 11 | Connected to: A connector 24% |
|
| I2pin 12 | Connected to: A connector 29% |
|
| I3pin 13 | Connected to: Signal 90% |
|
| GSpin 14 | Connected to: Not connected 62% · a signal 38% | — |
| EOpin 15 | Connected to: Not connected 81% · a signal 19% | — |
| VCCpin 16 | Connected to: 5V 100% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include 68000 by jefftranter, .C68 by ProbablyNotArtyom, M68kcomp1 by jtsiomb and Yddraig by ddraig68k.
The 74LS148 in open source designs
The gallery holds 30 open source boards using the 74LS148 from 21 GitHub repositories; a typical one measures about 121.1 × 97.9 mm and carries around 60 components.
53% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is 68000 by jefftranter.
Parts used alongside the 74LS148
Microcontrollers on boards using the 74LS148
What boards using the 74LS148 are built for
74LS148: common questions
Where can I find a 74LS148 reference design?
Each of the 30 boards on this page is a real design using the 74LS148. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the 74LS148 EI pin connected?
The EI pin is tied to GND on 18 of 21 designs (a signal on 2). Counted from the KiCad layouts of 21 open source designs using the 74LS148.
How is the 74LS148 EO pin connected?
The EO pin is left unconnected on 17 of 21 designs (a signal on 4). Counted from the KiCad layouts of 21 open source designs using the 74LS148.
What pull-up resistor is used on the 74LS148 I2 pin?
The I2 pin has a pull-up to 5V on 13 of 21 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 21 open source designs using the 74LS148.
What parts are used alongside the 74LS148?
The 74LS04, SST39SF040, 74LS245, 74LS32 and 74LS00 appear in the most repositories here.
Which microcontrollers do boards using the 74LS148 use?
Most are built on PIC (3), AVR/Arduino (2) and STM32 (1).
How big is a typical board using the 74LS148?
The median is 121.1 × 97.9 mm, and 53% are two-layer designs.
What is the most popular open source board using the 74LS148?
By GitHub stars, 68000 by jefftranter, with 132 stars.
Can I simulate one of these boards using the 74LS148 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.