57 open source boards using the MCP1700T-3302E/TT
Real designs built with the MCP1700T-3302E/TT, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Ferris
pierrechevalier83
208.8 × 86.8 mm102 parts2LSHL-2.11.3kSTM32
LinUSBConverter
uCAN-LIN
17.8 × 34 mm27 parts2LGPL-3.092STM32
USB-LED-Otter
Jana-Marie
12 × 15 mm14 parts2LCERN-OHL-1.264AVR/Arduino
Gpstracker
blemasle
79.3 × 59.2 mm65 parts2LMIT33GPS Mezzanine
96boards
85 × 54 mm32 parts2LNo license32STM32
Anticheww
AcheronProject
303.2 × 94.2 mm419 parts2LCustom license25TeensyShield progLED
samuelclay
110 × 80 mm77 parts2LNo license16Dc scm breakout board
antmicro
108 × 70 mm274 parts6LApache-2.09STM32
Knox-Key
Kingdragoncat
31.2 × 17.1 mm29 parts2LGPL-3.05STM32
Phalanx
rasch
187.2 × 77.2 mm86 parts2LSHL-2.14STM32
Legshark65 rev2
jemmec
285.8 × 95.3 mm202 parts2LMIT3RP2040/RP2350
Boardstorm x3
shashwtd
21 × 51 mm48 parts2LNo license3Egg LDO 250
Plaenkler
14 × 15 mm10 parts2LBSD-3-Clause3STM32
Kryptonite
samienr
26.3 × 17.1 mm27 parts2LMIT2RP2040/RP2350
Pico Button Board
RealtimeRoboticsGroup
55.9 × 111.8 mm201 parts4LSHL-2.11Lora daq module
danielkm-ee
70 × 40 mm78 parts4LMIT1AVR/Arduino
Celeste
wyolum
80 × 80 mm45 parts2LMIT1ESP32
Cc1101 receiver esp32
maxim75
49 × 55 mm39 parts4LNo license1RP2040/RP2350
Moonboard
newtontriumphant
22.3 × 52.2 mm37 parts2LNo license1KETCube mainBoard
SmartCAMPUSZCU
32 × 32 mm35 parts2LMIT1- schematic only · 1344 partsRP2040/RP2350
LZ-1-Backplane
HynixCJR
1344 parts2LNo license1 STM32
87keyboard
danielpclin
347.7 × 123.8 mm403 parts2LNo license0RP2040/RP2350
Cv module
pythagorean-comma
107 × 233.6 mm289 parts4LNo license0Crab robot
triluongmh-byte
110 × 80 mm113 parts4LNo license0AVR/Arduino
Sangaboard
kitspace-test-repos
65 × 56.5 mm85 parts2LCustom license0AVR/Arduino
Ugrow3
Dhyan-M
70 × 45 mm77 parts2LNo license0RP2040/RP2350
Ntp devboard
vighnesh-sawant
42.4 × 51 mm72 parts4LNo license0STM32
CentralCommand
AlanFord
61.2 × 54.5 mm55 parts2LNo license0STM32
OE-PyBoard
oeps-tech
33 × 41.9 mm55 parts4LNo license0ESP32
ESP32-H2-Matter-Button
Tee6
32 × 32 mm54 parts4LNo license0Nordic nRF
BoSL Camera dev
Monash-BoSL
78.2 × 100 mm50 parts2LNo license0STM32
Camel
metaquantus
55 × 28 mm49 parts4LMIT0Raspberry Pi
Devboard
LeoMos10
29.7 × 51 mm45 parts2LGPL-2.00RP2040/RP2350
TurtleBoard
chickenfried42
21 × 51 mm36 parts2LNo license0AVR/Arduino
Kicad sensor interface board
RangeMaster370
54 × 42 mm36 parts2LNo license0ESP32
Lax
smoore2386
18 × 25 mm34 parts2LNo license0
How designs wire the MCP1700T-3302E/TT
Read from the KiCad layouts of 47 open source designs, one per repository: what each pin of the MCP1700T-3302E/TT connects to, and the resistors, capacitors and other passives placed on it.
- The VO pin has a decoupling capacitor on 39 of 47 designs, most often 100 nF (then 10 µF).
- The VI pin has a decoupling capacitor on 38 of 47 designs, most often 10 µF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 94% | — |
| VOpin 2 | Connected to: 3.3V 83% |
|
| VIpin 3 | Connected to: VBUS 72% · a signal 28% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Ferris by pierrechevalier83, Meiji Led Ring by gregdavill, LinUSBConverter by uCAN-LIN and USB-LED-Otter by Jana-Marie.
The MCP1700T-3302E/TT in open source designs
The gallery holds 57 open source boards using the MCP1700T-3302E/TT from 53 GitHub repositories; a typical one measures about 54 × 51 mm and carries around 45 components.
75% are two-layer designs, the rest use four layers or more, and 35% carry an open source license.
The most starred is Ferris by pierrechevalier83.
Parts used alongside the MCP1700T-3302E/TT
Microcontrollers on boards using the MCP1700T-3302E/TT
What boards using the MCP1700T-3302E/TT are built for
MCP1700T-3302E/TT: common questions
Where can I find a MCP1700T-3302E/TT reference design?
Each of the 57 boards on this page is a real design using the MCP1700T-3302E/TT. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MCP1700T-3302E/TT VO pin?
The VO pin has a decoupling capacitor on 39 of 47 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 47 open source designs using the MCP1700T-3302E/TT.
What decoupling capacitors do designs use on the MCP1700T-3302E/TT VI pin?
The VI pin has a decoupling capacitor on 38 of 47 designs, most often 10 µF (then 1 µF). Counted from the KiCad layouts of 47 open source designs using the MCP1700T-3302E/TT.
What parts are used alongside the MCP1700T-3302E/TT?
The RP2040, W25Q16JVUXIQ, USBLC6-2SC6, ATECC608B-MAHDA-S and ATMEGA328P-AU appear in the most repositories here.
Which microcontrollers do boards using the MCP1700T-3302E/TT use?
Most are built on RP2040/RP2350 (15), STM32 (13), AVR/Arduino (6) and ESP32 (4).
How big is a typical board using the MCP1700T-3302E/TT?
The median is 54 × 51 mm, and 75% are two-layer designs.
What is the most popular open source board using the MCP1700T-3302E/TT?
By GitHub stars, Ferris by pierrechevalier83, with 1,271 stars.
Can I simulate one of these boards using the MCP1700T-3302E/TT before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.